11 May 2010
Flow Chart of Stitching Section of Towel Manufacturing | Working Procedure of Stitching Section
Stitching:
Stitching is the last section of towel manufacturing. In stitching section work is done according to the following flowchart:
The Working Procedure of Stitching Section:
» At first material is received from wet processing department. Then roll cutting i.e., warp way separation is done manually by using knife.
» Then the towels go to ribbon section. Here 2 long sides 9Selvedges) are stitched.
» Up next; comes the piece cutting section. Here small pitches of towels are separated from a large piece by cutting with a scissor.
» Then by using over lock m/c the 4 selvedges of the small towels are sewn.
» Then level is attached with the towel by sewing this is known as level sewing.
» Then the towels are sent to the quality Control Section where they are graded as A/B/C/D grade.
» Next the towels are sent to the special QC for further quality check-up.
» Then they are sent to the quality audit section. If the towels pass in this section then they are sent to the level confirm section.
» In level confirm section the levels are checked in order to assure the correct level has attached.
» Then the towel are folded in the folding section & then packed in a poly bag.
» Then they are sent for quality assurance audit.
» If the towels pass in the audit; then cartooning is done according to the Spec Sheet.
» Next final inspection is done. If everything is found ok in the final inspection; then the towels are sent for shipment.
 |
| Towel |
Flow Chart Of Stitching Section:
Inventory Receiving
↓
Role Cutting
↓
Ribbon Section
↓
Piece Cutting
↓
Over Lock
↓
Level Sewing
↓
QC Section
↓
Special QC
↓
Quality Audit
↓
Level Confirm
↓
Folding
↓
Packing
↓
QA Audit
↓
Cartooning
↓
Final Inspection
↓
Shipment
Inventory Receiving
↓
Role Cutting
↓
Ribbon Section
↓
Piece Cutting
↓
Over Lock
↓
Level Sewing
↓
QC Section
↓
Special QC
↓
Quality Audit
↓
Level Confirm
↓
Folding
↓
Packing
↓
QA Audit
↓
Cartooning
↓
Final Inspection
↓
Shipment
The Working Procedure of Stitching Section:
» At first material is received from wet processing department. Then roll cutting i.e., warp way separation is done manually by using knife.
» Then the towels go to ribbon section. Here 2 long sides 9Selvedges) are stitched.
» Up next; comes the piece cutting section. Here small pitches of towels are separated from a large piece by cutting with a scissor.
» Then by using over lock m/c the 4 selvedges of the small towels are sewn.
» Then level is attached with the towel by sewing this is known as level sewing.
» Then the towels are sent to the quality Control Section where they are graded as A/B/C/D grade.
» Next the towels are sent to the special QC for further quality check-up.
» Then they are sent to the quality audit section. If the towels pass in this section then they are sent to the level confirm section.
» In level confirm section the levels are checked in order to assure the correct level has attached.
» Then the towel are folded in the folding section & then packed in a poly bag.
» Then they are sent for quality assurance audit.
» If the towels pass in the audit; then cartooning is done according to the Spec Sheet.
» Next final inspection is done. If everything is found ok in the final inspection; then the towels are sent for shipment.
Subscribe to:
Post Comments
(Atom)
0 comments:
Post a Comment